Backflow Incense Holders

The waterfall stand for a backflow cone consists of two levels. First, a small elevation on which the cone is placed, and from it a groove runs downward, along which the smoke flows down and off the edge of the stand. A regular flat cone stand is built much more simply: it holds the cone upright and collects the ash in one place. It has neither of these two levels — no elevation, no groove.

If you place a backflow cone on such a flat stand, the smoke that is supposed to flow down in a ribbon will disperse at the base almost immediately, and the effect will be lost within the first seconds. Waterfall stands for incense solve this problem: the elevation raises the cone above the edge, and the groove directs the smoke in one direction, so the flow has time to gather and stream downward.

Elevation and groove: why a waterfall stand has two levels

The cone stands on the elevation. This is a platform a few centimeters high, with a flat or slightly concave pad on top. You place the cone in its center, and the smoke, which is supposed to flow down, starts already above the edge of the table. Over that short distance to the groove, the smoke flow has time to gather into a dense ribbon instead of spreading into the air right away.

From the pad with the cone, a groove runs downward. This is a narrow channel cut or cast into the body of the stand. Its depth and slope set the smoke's path: a groove that is too wide and flat lets the flow spread sideways, while a groove with clear edges keeps the smoke gathered all the way to the edge. Further on, the flow spills over the edge of the stand and becomes visible there as a real waterfall.

A regular flat stand doesn't need these levels and manages fine without them. But if you place a backflow cone on it, the smoke will roll off the sides of the stand in all directions almost immediately after starting, and you won't be able to see a dense flow.

What determines whether the smoke flows as a ribbon or disperses

How impressively the smoke flows depends on the stand under the cone almost as much as on the cone itself. Practitioners in the showroom first look at a few things: the height of the elevation, the width and slope of the groove, and the stand's material.

• Is the elevation too low? Then the smoke doesn't have time to gain the height needed to build up speed, and instead of a dense flow you get a thin, barely visible thread.

• A groove that's too wide or too shallow. The smoke spreads across the full width of the channel, and instead of a ribbon flowing to the edge, you get a weak, dispersed cloud.

• If the groove's slope is too steep or too gentle, the smoke breaks off in jerks on a sharp slope and barely moves toward the edge on a gentle one.

• A dark matte stand material. On such a surface the smoke flow is visible with more contrast, because it doesn't reflect light and doesn't create glare that blurs the picture.

• It's harder to make out the flow on a light glossy stand because of glare on the shiny surface, even though the speed and shape of the flow don't change.

Choosing the height and material for your cone and viewing spot

The same waterfall stand can work great with one cone and barely show the effect with another. Cones differ in smoke density and burn rate, and before matching a stand to a cone a practitioner will ask: how much smoke does this particular cone give off, and how fast does it burn? The answer determines what elevation height and groove depth will suit it. So before buying, it's worth checking the stand not only against the cone but also against the place where you'll be watching it: on a windowsill in daylight, in a darkened room, or on an altar where the stand is seen from the side. In the showroom on Bessarabska Square, a practitioner will place several options side by side and show how the smoke behaves in real light, because the angle and lighting in photos often hide a weak flow.

• Loyalty program: a cumulative discount from 1 to 10%, promo codes, and a discount on the store's birthday arrive in the newsletter.

• Only practitioners consult, and they'll honestly tell you if a stand won't suit your cone.

• Orders are put together and shipped the same day.

• Payment by card online, by bank details, cash on delivery with a 150 UAH prepayment, or cash in the showroom.

• Delivery by Nova Poshta and Ukrposhta works within Ukraine and abroad, and a courier can be called for Kyiv and the surrounding suburbs.

• Only original products, no replicas.

Buying a waterfall stand separately from the cone is common — it's usually chosen by people who have already settled on a cone and a spot where the smoke will be visible. It isn't hard to buy, and a practitioner in the showroom usually matches the pedestal height and groove depth to your specific piece right away, so the flow doesn't get lost in the first seconds. The exact price is listed on each product's page. Before ordering, you can see the stand in person and try it right away with a cone in the showroom at Bessarabska Square 2, Metrograd Mall, entrance from Khreshchatyk, and orders are delivered by Nova Poshta and Ukrposhta within Ukraine and abroad.

Frequently asked questions about waterfall stands for incense

The cone itself raises the fewest questions: it's the waterfall stand that people need to sort out more often, because it determines whether you'll see the effect or not. It's what gets asked about most in the showroom and in messages.

Will a regular flat stand work for a backflow cone

No. A regular stand has neither an elevation nor a groove, so a backflow cone's smoke gets no run-up. Such a cone on a flat stand will disperse at the base almost immediately, and you won't see the waterfall effect. You need a stand with both levels, directing the smoke flow to the edge.

Why is the effect weak even though the cone was chosen correctly

If the cone is matched correctly and the flow is still barely noticeable, the cause is more often worth looking for in the stand. A draft from a window, a fan, or an open door pushes the smoke sideways even before it reaches the groove. A groove that's too wide or too gentle gives the same result: the smoke spreads across the channel instead of flowing as a single ribbon.

How to clean soot from the groove

Soot in the groove settles as a thin layer and over time changes how the smoke flows down it. Remove it with a dry soft cloth or brush right after the stand cools down, without waiting for a thick layer to build up. If the soot has already set, wipe the groove with a cloth lightly dampened with water, and let the stand dry completely before the next incense session.

Payment methods

An order can be paid by card online or by bank details right at checkout. Cash on delivery with a 150 UAH prepayment is also available, if it's more convenient to pay the courier or at the branch upon pickup. In the showroom on Bessarabska Square, you can pay cash on the spot, without prepayment or transfers.